fork(1) download
copy 
  1. /*
  2.     This file is part of Repetier-Firmware.
  3.  
  4.     Repetier-Firmware is free software: you can redistribute it and/or modify
  5.     it under the terms of the GNU General Public License as published by
  6.     the Free Software Foundation, either version 3 of the License, or
  7.     (at your option) any later version.
  8.  
  9.     Repetier-Firmware is distributed in the hope that it will be useful,
  10.     but WITHOUT ANY WARRANTY; without even the implied warranty of
  11.     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  12.     GNU General Public License for more details.
  13.  
  14.     You should have received a copy of the GNU General Public License
  15.     along with Repetier-Firmware.  If not, see [www.gnu.org].
  16.  
  17. */
  18.  
  19. #ifndef CONFIGURATION_H
  20. #define CONFIGURATION_H
  21.  
  22. /**************** READ FIRST ************************
  23.  
  24.    This configuration file was created with the configuration tool. For that
  25.    reason, it does not contain the same informations as the original Configuration.h file.
  26.    It misses the comments and unused parts. Open this file file in the config tool
  27.    to see and change the data. You can also upload it to newer/older versions. The system
  28.    will silently add new options, so compilation continues to work.
  29.  
  30.    This file is optimized for version 0.91
  31.    generator: [www.repetier.com]
  32. */
  33.  
  34. #define NUM_EXTRUDER 1
  35. #define MOTHERBOARD 63
  36.  
  37. #include "pins.h"
  38.  
  39. // ################## EDIT THESE SETTINGS MANUALLY ################
  40. // ################ END MANUAL SETTINGS ##########################
  41.  
  42. #define FAN_BOARD_PIN -1
  43. //#define EXTERNALSERIAL  use Arduino serial library instead of build in. Requires more ram, has only 63 byte input buffer.
  44. // Uncomment the following line if you are using arduino compatible firmware made for Arduino version earlier then 1.0
  45. // If it is incompatible you will get compiler errors about write functions not beeing compatible!
  46. //#define COMPAT_PRE1
  47.  
  48.  
  49. #define DRIVE_SYSTEM 0
  50. #define XAXIS_STEPS_PER_MM 100
  51. #define YAXIS_STEPS_PER_MM 100
  52. #define ZAXIS_STEPS_PER_MM 407
  53. #define EXTRUDER_FAN_COOL_TEMP 50
  54. #define EXT0_X_OFFSET 0
  55. #define EXT0_Y_OFFSET 0
  56. #define EXT0_STEPS_PER_MM 95
  57. #define EXT0_TEMPSENSOR_TYPE 97
  58. #define EXT0_TEMPSENSOR_PIN TEMP_0_PIN
  59. #define EXT0_HEATER_PIN HEATER_0_PIN
  60. #define EXT0_STEP_PIN E0_STEP_PIN
  61. #define EXT0_DIR_PIN E0_DIR_PIN
  62. #define EXT0_INVERSE 1
  63. #define EXT0_ENABLE_PIN E0_ENABLE_PIN
  64. #define EXT0_ENABLE_ON 0
  65. #define EXT0_MAX_FEEDRATE 50
  66. #define EXT0_MAX_START_FEEDRATE 20
  67. #define EXT0_MAX_ACCELERATION 5000
  68. #define EXT0_HEAT_MANAGER 3
  69. #define EXT0_WATCHPERIOD 1
  70. #define EXT0_PID_INTEGRAL_DRIVE_MAX 230
  71. #define EXT0_PID_INTEGRAL_DRIVE_MIN 40
  72. #define EXT0_PID_P 7
  73. #define EXT0_PID_I 2
  74. #define EXT0_PID_D 40
  75. #define EXT0_PID_MAX 255
  76. #define EXT0_ADVANCE_K 0
  77. #define EXT0_ADVANCE_L 0
  78. #define EXT0_ADVANCE_BACKLASH_STEPS 0
  79. #define EXT0_WAIT_RETRACT_TEMP 150
  80. #define EXT0_WAIT_RETRACT_UNITS 0
  81. #define EXT0_SELECT_COMMANDS ""
  82. #define EXT0_DESELECT_COMMANDS ""
  83. #define EXT0_EXTRUDER_COOLER_PIN -1
  84. #define EXT0_EXTRUDER_COOLER_SPEED 255
  85. #define RETRACT_DURING_HEATUP true
  86. #define PID_CONTROL_RANGE 20
  87. #define SKIP_M109_IF_WITHIN 2
  88. #define SCALE_PID_TO_MAX 0
  89. #define TEMP_HYSTERESIS 0
  90. #define EXTRUDE_MAXLENGTH 160
  91. #define NUM_TEMPS_USERTHERMISTOR0 0
  92. #define USER_THERMISTORTABLE0 {}
  93. #define NUM_TEMPS_USERTHERMISTOR1 0
  94. #define USER_THERMISTORTABLE1 {}
  95. #define NUM_TEMPS_USERTHERMISTOR2 0
  96. #define USER_THERMISTORTABLE2 {}
  97. #define USE_GENERIC_THERMISTORTABLE_1
  98. #define GENERIC_THERM1_T0 25
  99. #define GENERIC_THERM1_R0 100000
  100. #define GENERIC_THERM1_BETA 3950
  101. #define GENERIC_THERM1_MIN_TEMP -20
  102. #define GENERIC_THERM1_MAX_TEMP 300
  103. #define GENERIC_THERM1_R1 0
  104. #define GENERIC_THERM1_R2 10000
  105. #define GENERIC_THERM_VREF 5
  106. #define GENERIC_THERM_NUM_ENTRIES 33
  107. #define HEATER_PWM_SPEED 0
  108.  
  109. // ############# Heated bed configuration ########################
  110.  
  111. #define HAVE_HEATED_BED 1
  112. #define HEATED_BED_MAX_TEMP 120
  113. #define SKIP_M190_IF_WITHIN 1
  114. #define HEATED_BED_SENSOR_TYPE 97
  115. #define HEATED_BED_SENSOR_PIN TEMP_1_PIN
  116. #define HEATED_BED_HEATER_PIN HEATER_1_PIN
  117. #define HEATED_BED_SET_INTERVAL 5000
  118. #define HEATED_BED_HEAT_MANAGER 0
  119. #define HEATED_BED_PID_INTEGRAL_DRIVE_MAX 255
  120. #define HEATED_BED_PID_INTEGRAL_DRIVE_MIN 80
  121. #define HEATED_BED_PID_PGAIN   196
  122. #define HEATED_BED_PID_IGAIN   33
  123. #define HEATED_BED_PID_DGAIN 290
  124. #define HEATED_BED_PID_MAX 255
  125. #define MIN_EXTRUDER_TEMP 150
  126. #define MAXTEMP 275
  127. #define MIN_DEFECT_TEMPERATURE -10
  128. #define MAX_DEFECT_TEMPERATURE 290
  129.  
  130. // ################ Endstop configuration #####################
  131.  
  132. #define ENDSTOP_PULLUP_X_MIN true
  133. #define ENDSTOP_X_MIN_INVERTING false
  134. #define MIN_HARDWARE_ENDSTOP_X true
  135. #define ENDSTOP_PULLUP_Y_MIN true
  136. #define ENDSTOP_Y_MIN_INVERTING false
  137. #define MIN_HARDWARE_ENDSTOP_Y true
  138. #define ENDSTOP_PULLUP_Z_MIN true
  139. #define ENDSTOP_Z_MIN_INVERTING false
  140. #define MIN_HARDWARE_ENDSTOP_Z true
  141. #define ENDSTOP_PULLUP_X_MAX true
  142. #define ENDSTOP_X_MAX_INVERTING false
  143. #define MAX_HARDWARE_ENDSTOP_X false
  144. #define ENDSTOP_PULLUP_Y_MAX true
  145. #define ENDSTOP_Y_MAX_INVERTING false
  146. #define MAX_HARDWARE_ENDSTOP_Y false
  147. #define ENDSTOP_PULLUP_Z_MAX true
  148. #define ENDSTOP_Z_MAX_INVERTING false
  149. #define MAX_HARDWARE_ENDSTOP_Z false
  150. #define max_software_endstop_r true
  151.  
  152. #define min_software_endstop_x false
  153. #define min_software_endstop_y false
  154. #define min_software_endstop_z false
  155. #define max_software_endstop_x true
  156. #define max_software_endstop_y true
  157. #define max_software_endstop_z true
  158. #define ENDSTOP_X_BACK_MOVE 5
  159. #define ENDSTOP_Y_BACK_MOVE 5
  160. #define ENDSTOP_Z_BACK_MOVE 1
  161. #define ENDSTOP_X_RETEST_REDUCTION_FACTOR 3
  162. #define ENDSTOP_Y_RETEST_REDUCTION_FACTOR 3
  163. #define ENDSTOP_Z_RETEST_REDUCTION_FACTOR 1
  164. #define ENDSTOP_X_BACK_ON_HOME 1
  165. #define ENDSTOP_Y_BACK_ON_HOME 1
  166. #define ENDSTOP_Z_BACK_ON_HOME 0
  167. #define ALWAYS_CHECK_ENDSTOPS 1
  168.  
  169. // ################# XYZ movements ###################
  170.  
  171. #define X_ENABLE_ON 0
  172. #define Y_ENABLE_ON 0
  173. #define Z_ENABLE_ON 0
  174. #define DISABLE_X 0
  175. #define DISABLE_Y 0
  176. #define DISABLE_Z 0
  177. #define DISABLE_E 0
  178. #define INVERT_X_DIR 0
  179. #define INVERT_Y_DIR 0
  180. #define INVERT_Z_DIR 0
  181. #define X_HOME_DIR -1
  182. #define Y_HOME_DIR -1
  183. #define Z_HOME_DIR -1
  184. #define X_MAX_LENGTH 200
  185. #define Y_MAX_LENGTH 200
  186. #define Z_MAX_LENGTH 180
  187. #define X_MIN_POS 0
  188. #define Y_MIN_POS 0
  189. #define Z_MIN_POS 0
  190.  
  191. // ##########################################################################################
  192. // ##                           Movement settings                                          ##
  193. // ##########################################################################################
  194.  
  195.  
  196. #define DELTA_SEGMENTS_PER_SECOND_PRINT 180 // Move accurate setting for print moves
  197. #define DELTA_SEGMENTS_PER_SECOND_MOVE 70 // Less accurate setting for other moves
  198.  
  199. // Delta settings
  200. #define DELTA_HOME_ON_POWER 0
  201.  
  202. #define MAX_DELTA_SEGMENTS_PER_LINE 24
  203. #define STEPPER_INACTIVE_TIME 360L
  204. #define MAX_INACTIVE_TIME 0L
  205. #define MAX_FEEDRATE_X 200
  206. #define MAX_FEEDRATE_Y 200
  207. #define MAX_FEEDRATE_Z 4
  208. #define HOMING_FEEDRATE_X 40
  209. #define HOMING_FEEDRATE_Y 40
  210. #define HOMING_FEEDRATE_Z 2
  211. #define HOMING_ORDER HOME_ORDER_XYZ
  212. #define ENABLE_BACKLASH_COMPENSATION 0
  213. #define X_BACKLASH 0
  214. #define Y_BACKLASH 0
  215. #define Z_BACKLASH 0
  216. #define RAMP_ACCELERATION 1
  217. #define STEPPER_HIGH_DELAY 0
  218. #define STEP_DOUBLER_FREQUENCY 12000
  219. #define ALLOW_QUADSTEPPING 1
  220. #define DOUBLE_STEP_DELAY 1 // time in microseconds
  221. #define MAX_HALFSTEP_INTERVAL 1999
  222. #define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 1000
  223. #define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y 1000
  224. #define MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z 100
  225. #define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 1000
  226. #define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y 1000
  227. #define MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z 100
  228. #define MAX_JERK 20
  229. #define MAX_ZJERK 0.3
  230. #define MOVE_CACHE_SIZE 16
  231. #define MOVE_CACHE_LOW 10
  232. #define LOW_TICKS_PER_MOVE 250000
  233. #define FEATURE_TWO_XSTEPPER 0
  234. #define X2_STEP_PIN   E1_STEP_PIN
  235. #define X2_DIR_PIN    E1_DIR_PIN
  236. #define X2_ENABLE_PIN E1_ENABLE_PIN
  237. #define FEATURE_TWO_YSTEPPER 0
  238. #define Y2_STEP_PIN   E1_STEP_PIN
  239. #define Y2_DIR_PIN    E1_DIR_PIN
  240. #define Y2_ENABLE_PIN E1_ENABLE_PIN
  241. #define FEATURE_TWO_ZSTEPPER 0
  242. #define Z2_STEP_PIN   E1_STEP_PIN
  243. #define Z2_DIR_PIN    E1_DIR_PIN
  244. #define Z2_ENABLE_PIN E1_ENABLE_PIN
  245. #define FEATURE_DITTO_PRINTING 0
  246.  
  247.  
  248. // ################# Misc. settings ##################
  249.  
  250. #define BAUDRATE 115200
  251. #define ENABLE_POWER_ON_STARTUP
  252. #define POWER_INVERTING 0
  253. #define KILL_METHOD 1
  254. #define GCODE_BUFFER_SIZE 2
  255. #define ACK_WITH_LINENUMBER
  256. #define WAITING_IDENTIFIER "wait"
  257. #define ECHO_ON_EXECUTE
  258. #define EEPROM_MODE 1
  259.  
  260. /* ======== Servos =======
  261. Control the servos with
  262. M340 P S   / ServoID = 0..3  pulseInUs = 500..2500
  263. Servos are controlled by a pulse width normally between 500 and 2500 with 1500ms in center position. 0 turns servo off.
  264. WARNING: Servos can draw a considerable amount of current. Make sure your system can handle this or you may risk your hardware!
  265. */
  266. #define FEATURE_SERVO 0
  267. #define SERVO0_PIN 11
  268. #define SERVO1_PIN -1
  269. #define SERVO2_PIN -1
  270. #define SERVO3_PIN -1
  271. #define FEATURE_WATCHDOG 0
  272.  
  273. // #################### Z-Probing #####################
  274.  
  275. #define FEATURE_Z_PROBE 0
  276. #define Z_PROBE_PIN -1
  277. #define Z_PROBE_PULLUP 0
  278. #define Z_PROBE_ON_HIGH 0
  279. #define Z_PROBE_X_OFFSET 0
  280. #define Z_PROBE_Y_OFFSET 0
  281. #define Z_PROBE_WAIT_BEFORE_TEST 0
  282. #define Z_PROBE_SPEED 2
  283. #define Z_PROBE_XY_SPEED 150
  284. #define Z_PROBE_SWITCHING_DISTANCE 1
  285. #define Z_PROBE_REPETITIONS 1
  286. #define Z_PROBE_HEIGHT 40
  287. #define Z_PROBE_START_SCRIPT ""
  288. #define Z_PROBE_FINISHED_SCRIPT ""
  289. #define FEATURE_AUTOLEVEL 1
  290. #define Z_PROBE_X1 20
  291. #define Z_PROBE_Y1 20
  292. #define Z_PROBE_X2 160
  293. #define Z_PROBE_Y2 20
  294. #define Z_PROBE_X3 100
  295. #define Z_PROBE_Y3 160
  296.  
  297. #ifndef SDSUPPORT  // Some boards have sd support on board. These define the values already in pins.h
  298. #define SDSUPPORT 0
  299. #define SDCARDDETECT -1
  300. #define SDCARDDETECTINVERTED 0
  301. #endif
  302. #define SD_EXTENDED_DIR 1 /** Show extended directory including file length. Don't use this with Pronterface! */
  303. #define ARC_SUPPORT 1
  304. #define FEATURE_MEMORY_POSITION 1
  305. #define FEATURE_CHECKSUM_FORCED 0
  306. #define FEATURE_FAN_CONTROL 1
  307. #define FEATURE_CONTROLLER 0
  308. #define UI_LANGUAGE 0
  309. #define UI_PRINTER_NAME "RepRap"
  310. #define UI_PRINTER_COMPANY "Home made"
  311. #define UI_PAGES_DURATION 4000
  312. #define UI_ANIMATION 1
  313. #define UI_DISABLE_AUTO_PAGESWITCH 1
  314. #define UI_AUTORETURN_TO_MENU_AFTER 30000
  315. #define FEATURE_UI_KEYS 0
  316. #define UI_ENCODER_SPEED 1
  317. #define UI_KEY_BOUNCETIME 10
  318. #define UI_KEY_FIRST_REPEAT 500
  319. #define UI_KEY_REDUCE_REPEAT 50
  320. #define UI_KEY_MIN_REPEAT 50
  321. #define FEATURE_BEEPER 0
  322. #define CASE_LIGHTS_PIN -1
  323. #define UI_START_SCREEN_DELAY 1000
  324. /**
  325. Beeper sound definitions for short beeps during key actions
  326. and longer beeps for important actions.
  327. Parameter is delay in microseconds and the secons is the number of repetitions.
  328. Values must be in range 1..255
  329. */
  330. #define BEEPER_SHORT_SEQUENCE 2,2
  331. #define BEEPER_LONG_SEQUENCE 8,8
  332. #define UI_SET_PRESET_HEATED_BED_TEMP_PLA 60
  333. #define UI_SET_PRESET_EXTRUDER_TEMP_PLA   190
  334. #define UI_SET_PRESET_HEATED_BED_TEMP_ABS 110
  335. #define UI_SET_PRESET_EXTRUDER_TEMP_ABS   240
  336. #define UI_SET_MIN_HEATED_BED_TEMP  30
  337. #define UI_SET_MAX_HEATED_BED_TEMP 120
  338. #define UI_SET_MIN_EXTRUDER_TEMP   170
  339. #define UI_SET_MAX_EXTRUDER_TEMP   260
  340. #define UI_SET_EXTRUDER_FEEDRATE 2
  341. #define UI_SET_EXTRUDER_RETRACT_DISTANCE 3
  342.  
  343. #endif
  344.  
  345. /* Below you will find the configuration string, that created this Configuration.h
  346.  
  347. ========== Start configuration string ==========
  348. {
  349.     "editMode": 1,
  350.     "processor": 0,
  351.     "baudrate": 115200,
  352.     "xStepsPerMM": 100,
  353.     "yStepsPerMM": 100,
  354.     "zStepsPerMM": 407,
  355.     "xInvert": 0,
  356.     "xInvertEnable": 0,
  357.     "eepromMode": 1,
  358.     "yInvert": 0,
  359.     "yInvertEnable": 0,
  360.     "zInvert": 0,
  361.     "zInvertEnable": 0,
  362.     "extruder": [
  363.         {
  364.             "id": 0,
  365.             "heatManager": 3,
  366.             "pidDriveMin": 40,
  367.             "pidDriveMax": 230,
  368.             "pidMax": 255,
  369.             "sensorType": 97,
  370.             "sensorPin": "TEMP_0_PIN",
  371.             "heaterPin": "HEATER_0_PIN",
  372.             "inverse": 0,
  373.             "maxFeedrate": 50,
  374.             "startFeedrate": 20,
  375.             "invert": "0",
  376.             "invertEnable": "0",
  377.             "acceleration": 5000,
  378.             "watchPeriod": 1,
  379.             "pidP": 7,
  380.             "pidI": 2,
  381.             "pidD": 40,
  382.             "advanceK": 0,
  383.             "advanceL": 0,
  384.             "waitRetractTemp": 150,
  385.             "waitRetractUnits": 0,
  386.             "waitRetract": 0,
  387.             "stepsPerMM": 95,
  388.             "coolerPin": -1,
  389.             "coolerSpeed": 255,
  390.             "selectCommands": "",
  391.             "deselectCommands": "",
  392.             "xOffset": 0,
  393.             "yOffset": 0,
  394.             "xOffsetSteps": 0,
  395.             "yOffsetSteps": 0,
  396.             "stepper": {
  397.                 "name": "Extruder 0",
  398.                 "step": "E0_STEP_PIN",
  399.                 "dir": "E0_DIR_PIN",
  400.                 "enable": "E0_ENABLE_PIN"
  401.             },
  402.             "advanceBacklashSteps": 0
  403.         }
  404.     ],
  405.     "uiLanguage": 0,
  406.     "uiController": 0,
  407.     "xMinEndstop": 2,
  408.     "yMinEndstop": 2,
  409.     "zMinEndstop": 2,
  410.     "xMaxEndstop": 0,
  411.     "yMaxEndstop": 0,
  412.     "zMaxEndstop": 0,
  413.     "motherboard": 63,
  414.     "driveSystem": 0,
  415.     "xMaxSpeed": 200,
  416.     "xHomingSpeed": 40,
  417.     "xTravelAcceleration": 1000,
  418.     "xPrintAcceleration": 1000,
  419.     "yMaxSpeed": 200,
  420.     "yHomingSpeed": 40,
  421.     "yTravelAcceleration": 1000,
  422.     "yPrintAcceleration": 1000,
  423.     "zMaxSpeed": 4,
  424.     "zHomingSpeed": 2,
  425.     "zTravelAcceleration": 100,
  426.     "zPrintAcceleration": 100,
  427.     "xMotor": {
  428.         "name": "X motor",
  429.         "step": "X_STEP_PIN",
  430.         "dir": "X_DIR_PIN",
  431.         "enable": "X_ENABLE_PIN"
  432.     },
  433.     "yMotor": {
  434.         "name": "Y motor",
  435.         "step": "Y_STEP_PIN",
  436.         "dir": "Y_DIR_PIN",
  437.         "enable": "Y_ENABLE_PIN"
  438.     },
  439.     "zMotor": {
  440.         "name": "Z motor",
  441.         "step": "Z_STEP_PIN",
  442.         "dir": "Z_DIR_PIN",
  443.         "enable": "Z_ENABLE_PIN"
  444.     },
  445.     "enableBacklash": "0",
  446.     "backlashX": 0,
  447.     "backlashY": 0,
  448.     "backlashZ": 0,
  449.     "stepperInactiveTime": 360,
  450.     "maxInactiveTime": 0,
  451.     "xMinPos": 0,
  452.     "yMinPos": 0,
  453.     "zMinPos": 0,
  454.     "xLength": 200,
  455.     "yLength": 200,
  456.     "zLength": 180,
  457.     "alwaysCheckEndstops": "1",
  458.     "disableX": "0",
  459.     "disableY": "0",
  460.     "disableZ": "0",
  461.     "disableE": "0",
  462.     "xHomeDir": "-1",
  463.     "yHomeDir": "-1",
  464.     "zHomeDir": "-1",
  465.     "xEndstopBack": 1,
  466.     "yEndstopBack": 1,
  467.     "zEndstopBack": 0,
  468.     "deltaSegmentsPerSecondPrint": 180,
  469.     "deltaSegmentsPerSecondTravel": 70,
  470.     "deltaDiagonalRod": 445,
  471.     "deltaHorizontalRadius": 209.25,
  472.     "deltaAlphaA": 210,
  473.     "deltaAlphaB": 330,
  474.     "deltaAlphaC": 90,
  475.     "deltaRadiusCorrA": 0,
  476.     "deltaRadiusCorrB": 0,
  477.     "deltaRadiusCorrC": 0,
  478.     "deltaXOffsetSteps": 0,
  479.     "deltaYOffsetSteps": 0,
  480.     "deltaZOffsetSteps": 0,
  481.     "deltaSegmentsPerLine": 24,
  482.     "stepperHighDelay": 0,
  483.     "stepDoublerFrequency": 12000,
  484.     "allowQuadstepping": "1",
  485.     "doubleStepDelay": 1,
  486.     "maxHalfstepInterval": 1999,
  487.     "maxJerk": 20,
  488.     "maxZJerk": 0.3,
  489.     "moveCacheSize": 16,
  490.     "moveCacheLow": 10,
  491.     "lowTicksPerMove": 250000,
  492.     "enablePowerOnStartup": "1",
  493.     "echoOnExecute": "1",
  494.     "sendWaits": "1",
  495.     "ackWithLineNumber": "1",
  496.     "killMethod": 1,
  497.     "useAdvance": "0",
  498.     "useQuadraticAdvance": "0",
  499.     "powerInverting": 0,
  500.     "mirrorX": 0,
  501.     "mirrorXMotor": {
  502.         "name": "Extruder 1",
  503.         "step": "E1_STEP_PIN",
  504.         "dir": "E1_DIR_PIN",
  505.         "enable": "E1_ENABLE_PIN"
  506.     },
  507.     "mirrorY": 0,
  508.     "mirrorYMotor": {
  509.         "name": "Extruder 1",
  510.         "step": "E1_STEP_PIN",
  511.         "dir": "E1_DIR_PIN",
  512.         "enable": "E1_ENABLE_PIN"
  513.     },
  514.     "mirrorZ": 0,
  515.     "mirrorZMotor": {
  516.         "name": "Extruder 1",
  517.         "step": "E1_STEP_PIN",
  518.         "dir": "E1_DIR_PIN",
  519.         "enable": "E1_ENABLE_PIN"
  520.     },
  521.     "dittoPrinting": "0",
  522.     "featureServos": "0",
  523.     "servo0Pin": 11,
  524.     "servo1Pin": -1,
  525.     "servo2Pin": -1,
  526.     "servo3Pin": -1,
  527.     "featureWatchdog": "0",
  528.     "hasHeatedBed": "1",
  529.     "enableZProbing": "0",
  530.     "extrudeMaxLength": 160,
  531.     "homeOrder": "HOME_ORDER_XYZ",
  532.     "featureController": 0,
  533.     "uiPrinterName": "RepRap",
  534.     "uiPrinterCompany": "Home made",
  535.     "uiPagesDuration": 4000,
  536.     "uiAnimation": "1",
  537.     "uiDisablePageswitch": "1",
  538.     "uiAutoReturnAfter": 30000,
  539.     "featureKeys": "0",
  540.     "uiEncoderSpeed": 1,
  541.     "uiKeyBouncetime": 10,
  542.     "uiKeyFirstRepeat": 500,
  543.     "uiKeyReduceRepeat": 50,
  544.     "uiKeyMinRepeat": 50,
  545.     "featureBeeper": "0",
  546.     "uiPresetBedTempPLA": 60,
  547.     "uiPresetBedABS": 110,
  548.     "uiPresetExtruderPLA": 190,
  549.     "uiPresetExtruderABS": 240,
  550.     "uiMinHeatedBed": 30,
  551.     "uiMaxHeatedBed": 120,
  552.     "uiMinEtxruderTemp": 170,
  553.     "uiMaxExtruderTemp": 260,
  554.     "uiExtruderFeedrate": 2,
  555.     "uiExtruderRetractDistance": 3,
  556.     "maxBedTemperature": 120,
  557.     "bedSensorType": 97,
  558.     "bedSensorPin": "TEMP_1_PIN",
  559.     "bedHeaterPin": "HEATER_1_PIN",
  560.     "bedHeatManager": 0,
  561.     "bedUpdateInterval": 5000,
  562.     "bedPidDriveMin": 80,
  563.     "bedPidDriveMax": 255,
  564.     "bedPidP": 196,
  565.     "bedPidI": 33,
  566.     "bedPidD": 290,
  567.     "bedPidMax": 255,
  568.     "caseLightPin": -1,
  569.     "bedSkipIfWithin": 1,
  570.     "gen1T0": 25,
  571.     "gen1R0": 100000,
  572.     "gen1Beta": 3950,
  573.     "gen1MinTemp": -20,
  574.     "gen1MaxTemp": 300,
  575.     "gen1R1": 0,
  576.     "gen1R2": 10000,
  577.     "gen2T0": 25,
  578.     "gen2R0": 100000,
  579.     "gen2Beta": 4036,
  580.     "gen2MinTemp": -20,
  581.     "gen2MaxTemp": 300,
  582.     "gen2R1": 0,
  583.     "gen2R2": 4700,
  584.     "gen3T0": 25,
  585.     "gen3R0": 100000,
  586.     "gen3Beta": 4036,
  587.     "gen3MinTemp": -20,
  588.     "gen3MaxTemp": 300,
  589.     "gen3R1": 0,
  590.     "gen3R2": 4700,
  591.     "userTable0": {
  592.         "r1": 0,
  593.         "r2": 10000,
  594.         "temps": [
  595.             {
  596.                 "t": 270,
  597.                 "r": 162,
  598.                 "adc": 136.44385026738
  599.             },
  600.             {
  601.                 "t": 290,
  602.                 "r": 119,
  603.                 "adc": 101.12160199211
  604.             },
  605.             {
  606.                 "t": 160,
  607.                 "r": 1314,
  608.                 "adc": 894.71732623878
  609.             },
  610.             {
  611.                 "t": 150,
  612.                 "r": 1665,
  613.                 "adc": 1071.1979575805
  614.             },
  615.             {
  616.                 "t": 210,
  617.                 "r": 457,
  618.                 "adc": 362.88830715532
  619.             },
  620.             {
  621.                 "t": 200,
  622.                 "r": 552,
  623.                 "adc": 430.39603960396
  624.             },
  625.             {
  626.                 "t": 230,
  627.                 "r": 319,
  628.                 "adc": 260.2719665272
  629.             },
  630.             {
  631.                 "t": 170,
  632.                 "r": 1051,
  633.                 "adc": 748.36463223787
  634.             },
  635.             {
  636.                 "t": 180,
  637.                 "r": 842,
  638.                 "adc": 622.15626127752
  639.             },
  640.             {
  641.                 "t": 190,
  642.                 "r": 677,
  643.                 "adc": 515.58768830203
  644.             },
  645.             {
  646.                 "t": 220,
  647.                 "r": 382,
  648.                 "adc": 307.80991735537
  649.             },
  650.             {
  651.                 "t": 250,
  652.                 "r": 224,
  653.                 "adc": 186.28757108042
  654.             },
  655.             {
  656.                 "t": 260,
  657.                 "r": 189,
  658.                 "adc": 158.30537942319
  659.             },
  660.             {
  661.                 "t": 240,
  662.                 "r": 266,
  663.                 "adc": 219.34554973822
  664.             },
  665.             {
  666.                 "t": 280,
  667.                 "r": 139,
  668.                 "adc": 117.62864228146
  669.             },
  670.             {
  671.                 "t": 60,
  672.                 "r": 24600,
  673.                 "adc": 3438.1228668942
  674.             },
  675.             {
  676.                 "t": 110,
  677.                 "r": 6550,
  678.                 "adc": 2384.2
  679.             },
  680.             {
  681.                 "t": 130,
  682.                 "r": 2812,
  683.                 "adc": 1532.8993610224
  684.             },
  685.             {
  686.                 "t": 140,
  687.                 "r": 2146,
  688.                 "adc": 1283.6503067485
  689.             },
  690.             {
  691.                 "t": 120,
  692.                 "r": 3702,
  693.                 "adc": 1804.2954058557
  694.             },
  695.             {
  696.                 "t": 100,
  697.                 "r": 6550,
  698.                 "adc": 2384.2
  699.             },
  700.             {
  701.                 "t": 90,
  702.                 "r": 8927,
  703.                 "adc": 2682.6201658472
  704.             },
  705.             {
  706.                 "t": 80,
  707.                 "r": 12350,
  708.                 "adc": 2966.1730205279
  709.             },
  710.             {
  711.                 "t": 70,
  712.                 "r": 17290,
  713.                 "adc": 3219.761255116
  714.             },
  715.             {
  716.                 "t": 50,
  717.                 "r": 35700,
  718.                 "adc": 3618.6014851485
  719.             },
  720.             {
  721.                 "t": 40,
  722.                 "r": 52930,
  723.                 "adc": 3761.0333159813
  724.             },
  725.             {
  726.                 "t": 30,
  727.                 "r": 80390,
  728.                 "adc": 3868.8100834411
  729.             },
  730.             {
  731.                 "t": 25,
  732.                 "r": 100000,
  733.                 "adc": 3911.1747851003
  734.             },
  735.             {
  736.                 "t": 20,
  737.                 "r": 125200,
  738.                 "adc": 3946.8360277136
  739.             },
  740.             {
  741.                 "t": 10,
  742.                 "r": 199700,
  743.                 "adc": 4000.8390410959
  744.             },
  745.             {
  746.                 "t": 0,
  747.                 "r": 325100,
  748.                 "adc": 4036.6419041844
  749.             }
  750.         ],
  751.         "numEntries": 31
  752.     },
  753.     "userTable1": {
  754.         "r1": 0,
  755.         "r2": 4700,
  756.         "temps": [
  757.  
  758.         ]
  759.     },
  760.     "userTable2": {
  761.         "r1": 0,
  762.         "r2": 4700,
  763.         "temps": [
  764.  
  765.         ]
  766.     },
  767.     "tempHysteresis": 0,
  768.     "pidControlRange": 20,
  769.     "skipM109Within": 2,
  770.     "extruderFanCoolTemp": 50,
  771.     "minTemp": 150,
  772.     "maxTemp": 275,
  773.     "minDefectTemp": -10,
  774.     "maxDefectTemp": 290,
  775.     "arcSupport": "1",
  776.     "featureMemoryPositionWatchdog": "1",
  777.     "forceChecksum": "0",
  778.     "sdExtendedDir": "1",
  779.     "featureFanControl": "1",
  780.     "fanPin": "FAN_PIN",
  781.     "scalePidToMax": 0,
  782.     "zProbePin": -1,
  783.     "zProbePullup": "0",
  784.     "zProbeOnHigh": "0",
  785.     "zProbeXOffset": 0,
  786.     "zProbeYOffset": 0,
  787.     "zProbeWaitBeforeTest": "0",
  788.     "zProbeSpeed": 2,
  789.     "zProbeXYSpeed": 150,
  790.     "zProbeHeight": 40,
  791.     "zProbeStartScript": "",
  792.     "zProbeFinishedScript": "",
  793.     "featureAutolevel": "1",
  794.     "zProbeX1": 20,
  795.     "zProbeY1": 20,
  796.     "zProbeX2": 160,
  797.     "zProbeY2": 20,
  798.     "zProbeX3": 100,
  799.     "zProbeY3": 160,
  800.     "zProbeSwitchingDistance": 1,
  801.     "zProbeRepetitions": 1,
  802.     "sdSupport": "0",
  803.     "sdCardDetectPin": -1,
  804.     "sdCardDetectInverted": "0",
  805.     "uiStartScreenDelay": 1000,
  806.     "xEndstopBackMove": 5,
  807.     "yEndstopBackMove": 5,
  808.     "zEndstopBackMove": 1,
  809.     "xEndstopRetestFactor": 3,
  810.     "yEndstopRetestFactor": 3,
  811.     "zEndstopRetestFactor": 3,
  812.     "xMinPin": "X_MIN_PIN",
  813.     "yMinPin": "Y_MIN_PIN",
  814.     "zMinPin": "Z_MIN_PIN",
  815.     "xMaxPin": "X_MAX_PIN",
  816.     "yMaxPin": "Y_MAX_PIN",
  817.     "zMaxPin": "Z_MAX_PIN",
  818.     "deltaHomeOnPower": "0",
  819.     "fanBoardPin": -1,
  820.     "heaterPWMSpeed": 0,
  821.     "hasMAX6675": false,
  822.     "hasMAX31855": false,
  823.     "hasGeneric1": true,
  824.     "hasGeneric2": false,
  825.     "hasGeneric3": false,
  826.     "hasUser0": false,
  827.     "hasUser1": false,
  828.     "hasUser2": false,
  829.     "numExtruder": 1,
  830.     "version": 91
  831. }
  832. ========== End configuration string ==========
  833.  
  834. */
Compilation error #stdin compilation error #stdout 0s 0KB
comments (?)
stdin
copy 
Standard input is empty
compilation info 
Main.java:19: error: illegal character: '#'
#ifndef CONFIGURATION_H
^
Main.java:20: error: illegal character: '#'
#define CONFIGURATION_H
^
Main.java:34: error: illegal character: '#'
#define NUM_EXTRUDER 1
^
Main.java:35: error: illegal character: '#'
#define MOTHERBOARD 63
^
Main.java:37: error: illegal character: '#'
#include "pins.h"
^
Main.java:42: error: illegal character: '#'
#define FAN_BOARD_PIN -1
^
Main.java:49: error: illegal character: '#'
#define DRIVE_SYSTEM 0
^
Main.java:50: error: illegal character: '#'
#define XAXIS_STEPS_PER_MM 100
^
Main.java:51: error: illegal character: '#'
#define YAXIS_STEPS_PER_MM 100
^
Main.java:52: error: illegal character: '#'
#define ZAXIS_STEPS_PER_MM 407
^
Main.java:53: error: illegal character: '#'
#define EXTRUDER_FAN_COOL_TEMP 50
^
Main.java:54: error: illegal character: '#'
#define EXT0_X_OFFSET 0
^
Main.java:55: error: illegal character: '#'
#define EXT0_Y_OFFSET 0
^
Main.java:56: error: illegal character: '#'
#define EXT0_STEPS_PER_MM 95
^
Main.java:57: error: illegal character: '#'
#define EXT0_TEMPSENSOR_TYPE 97
^
Main.java:58: error: illegal character: '#'
#define EXT0_TEMPSENSOR_PIN TEMP_0_PIN
^
Main.java:59: error: illegal character: '#'
#define EXT0_HEATER_PIN HEATER_0_PIN
^
Main.java:60: error: illegal character: '#'
#define EXT0_STEP_PIN E0_STEP_PIN
^
Main.java:61: error: illegal character: '#'
#define EXT0_DIR_PIN E0_DIR_PIN
^
Main.java:62: error: illegal character: '#'
#define EXT0_INVERSE 1
^
Main.java:63: error: illegal character: '#'
#define EXT0_ENABLE_PIN E0_ENABLE_PIN
^
Main.java:64: error: illegal character: '#'
#define EXT0_ENABLE_ON 0
^
Main.java:65: error: illegal character: '#'
#define EXT0_MAX_FEEDRATE 50
^
Main.java:66: error: illegal character: '#'
#define EXT0_MAX_START_FEEDRATE 20
^
Main.java:67: error: illegal character: '#'
#define EXT0_MAX_ACCELERATION 5000
^
Main.java:68: error: illegal character: '#'
#define EXT0_HEAT_MANAGER 3
^
Main.java:69: error: illegal character: '#'
#define EXT0_WATCHPERIOD 1
^
Main.java:70: error: illegal character: '#'
#define EXT0_PID_INTEGRAL_DRIVE_MAX 230
^
Main.java:71: error: illegal character: '#'
#define EXT0_PID_INTEGRAL_DRIVE_MIN 40
^
Main.java:72: error: illegal character: '#'
#define EXT0_PID_P 7
^
Main.java:73: error: illegal character: '#'
#define EXT0_PID_I 2
^
Main.java:74: error: illegal character: '#'
#define EXT0_PID_D 40
^
Main.java:75: error: illegal character: '#'
#define EXT0_PID_MAX 255
^
Main.java:76: error: illegal character: '#'
#define EXT0_ADVANCE_K 0
^
Main.java:77: error: illegal character: '#'
#define EXT0_ADVANCE_L 0
^
Main.java:78: error: illegal character: '#'
#define EXT0_ADVANCE_BACKLASH_STEPS 0
^
Main.java:79: error: illegal character: '#'
#define EXT0_WAIT_RETRACT_TEMP 150
^
Main.java:80: error: illegal character: '#'
#define EXT0_WAIT_RETRACT_UNITS 0
^
Main.java:81: error: illegal character: '#'
#define EXT0_SELECT_COMMANDS ""
^
Main.java:82: error: illegal character: '#'
#define EXT0_DESELECT_COMMANDS ""
^
Main.java:83: error: illegal character: '#'
#define EXT0_EXTRUDER_COOLER_PIN -1
^
Main.java:84: error: illegal character: '#'
#define EXT0_EXTRUDER_COOLER_SPEED 255
^
Main.java:85: error: illegal character: '#'
#define RETRACT_DURING_HEATUP true
^
Main.java:86: error: illegal character: '#'
#define PID_CONTROL_RANGE 20
^
Main.java:87: error: illegal character: '#'
#define SKIP_M109_IF_WITHIN 2
^
Main.java:88: error: illegal character: '#'
#define SCALE_PID_TO_MAX 0
^
Main.java:89: error: illegal character: '#'
#define TEMP_HYSTERESIS 0
^
Main.java:90: error: illegal character: '#'
#define EXTRUDE_MAXLENGTH 160
^
Main.java:91: error: illegal character: '#'
#define NUM_TEMPS_USERTHERMISTOR0 0
^
Main.java:92: error: illegal character: '#'
#define USER_THERMISTORTABLE0 {}
^
Main.java:93: error: illegal character: '#'
#define NUM_TEMPS_USERTHERMISTOR1 0
^
Main.java:94: error: illegal character: '#'
#define USER_THERMISTORTABLE1 {}
^
Main.java:95: error: illegal character: '#'
#define NUM_TEMPS_USERTHERMISTOR2 0
^
Main.java:96: error: illegal character: '#'
#define USER_THERMISTORTABLE2 {}
^
Main.java:97: error: illegal character: '#'
#define USE_GENERIC_THERMISTORTABLE_1
^
Main.java:98: error: illegal character: '#'
#define GENERIC_THERM1_T0 25
^
Main.java:99: error: illegal character: '#'
#define GENERIC_THERM1_R0 100000
^
Main.java:100: error: illegal character: '#'
#define GENERIC_THERM1_BETA 3950
^
Main.java:101: error: illegal character: '#'
#define GENERIC_THERM1_MIN_TEMP -20
^
Main.java:102: error: illegal character: '#'
#define GENERIC_THERM1_MAX_TEMP 300
^
Main.java:103: error: illegal character: '#'
#define GENERIC_THERM1_R1 0
^
Main.java:104: error: illegal character: '#'
#define GENERIC_THERM1_R2 10000
^
Main.java:105: error: illegal character: '#'
#define GENERIC_THERM_VREF 5
^
Main.java:106: error: illegal character: '#'
#define GENERIC_THERM_NUM_ENTRIES 33
^
Main.java:107: error: illegal character: '#'
#define HEATER_PWM_SPEED 0
^
Main.java:111: error: illegal character: '#'
#define HAVE_HEATED_BED 1
^
Main.java:112: error: illegal character: '#'
#define HEATED_BED_MAX_TEMP 120
^
Main.java:113: error: illegal character: '#'
#define SKIP_M190_IF_WITHIN 1
^
Main.java:114: error: illegal character: '#'
#define HEATED_BED_SENSOR_TYPE 97
^
Main.java:115: error: illegal character: '#'
#define HEATED_BED_SENSOR_PIN TEMP_1_PIN
^
Main.java:116: error: illegal character: '#'
#define HEATED_BED_HEATER_PIN HEATER_1_PIN
^
Main.java:117: error: illegal character: '#'
#define HEATED_BED_SET_INTERVAL 5000
^
Main.java:118: error: illegal character: '#'
#define HEATED_BED_HEAT_MANAGER 0
^
Main.java:119: error: illegal character: '#'
#define HEATED_BED_PID_INTEGRAL_DRIVE_MAX 255
^
Main.java:120: error: illegal character: '#'
#define HEATED_BED_PID_INTEGRAL_DRIVE_MIN 80
^
Main.java:121: error: illegal character: '#'
#define HEATED_BED_PID_PGAIN   196
^
Main.java:122: error: illegal character: '#'
#define HEATED_BED_PID_IGAIN   33
^
Main.java:123: error: illegal character: '#'
#define HEATED_BED_PID_DGAIN 290
^
Main.java:124: error: illegal character: '#'
#define HEATED_BED_PID_MAX 255
^
Main.java:125: error: illegal character: '#'
#define MIN_EXTRUDER_TEMP 150
^
Main.java:126: error: illegal character: '#'
#define MAXTEMP 275
^
Main.java:127: error: illegal character: '#'
#define MIN_DEFECT_TEMPERATURE -10
^
Main.java:128: error: illegal character: '#'
#define MAX_DEFECT_TEMPERATURE 290
^
Main.java:132: error: illegal character: '#'
#define ENDSTOP_PULLUP_X_MIN true
^
Main.java:133: error: illegal character: '#'
#define ENDSTOP_X_MIN_INVERTING false
^
Main.java:134: error: illegal character: '#'
#define MIN_HARDWARE_ENDSTOP_X true
^
Main.java:135: error: illegal character: '#'
#define ENDSTOP_PULLUP_Y_MIN true
^
Main.java:136: error: illegal character: '#'
#define ENDSTOP_Y_MIN_INVERTING false
^
Main.java:137: error: illegal character: '#'
#define MIN_HARDWARE_ENDSTOP_Y true
^
Main.java:138: error: illegal character: '#'
#define ENDSTOP_PULLUP_Z_MIN true
^
Main.java:139: error: illegal character: '#'
#define ENDSTOP_Z_MIN_INVERTING false
^
Main.java:140: error: illegal character: '#'
#define MIN_HARDWARE_ENDSTOP_Z true
^
Main.java:141: error: illegal character: '#'
#define ENDSTOP_PULLUP_X_MAX true
^
Main.java:142: error: illegal character: '#'
#define ENDSTOP_X_MAX_INVERTING false
^
Main.java:143: error: illegal character: '#'
#define MAX_HARDWARE_ENDSTOP_X false
^
Main.java:144: error: illegal character: '#'
#define ENDSTOP_PULLUP_Y_MAX true
^
Main.java:145: error: illegal character: '#'
#define ENDSTOP_Y_MAX_INVERTING false
^
Main.java:146: error: illegal character: '#'
#define MAX_HARDWARE_ENDSTOP_Y false
^
Main.java:147: error: illegal character: '#'
#define ENDSTOP_PULLUP_Z_MAX true
^
Main.java:148: error: illegal character: '#'
#define ENDSTOP_Z_MAX_INVERTING false
^
100 errors
stdout
copy 
Standard output is empty
https://ideone.com/fWRsIJ
language:
Java (HotSpot 12)
created:
9 years ago
visibility:
public

Share or Embed source code

Discover > Sphere Engine API

The brand new service which powers Ideone!

Discover > IDE Widget

Widget for compiling and running the source code in a web browser!